T: 01793 422 040

T: 01793 422 040

E: sales@draindepot.co.uk

115mm x 3m Half Round Copper Gutter

SKU: CP100HRG
£58.06 Ex VAT £69.67 Inc VAT

1  Carriage is charged on each order. It is charged  per order not per product and varies between £7 and £16 dependent on the size & weight of the product (exc highlands & islands). This item will be delivered within 2 working days if ordered before 2.30pm, more details 

1 Returns are free, you just have to get it back to us, more details

Product Description

Product Description

115mm x 3m length of real copper deep run half round gutter with front facing decorative rolled bead edge. Gutter unions will be required to join two lengths together. Please click the second image for overall product dimensions.

Benefits of Real Cooper Gutter:

Lightweight, stylish and strong                                                              

Environmentally friendly and fully recyclable  

Easy to install dry joint system                                                               

Stable material with very minimum thermal expansion

Push-fit stop-ends with EDPM rubber seal                      

Fascia brackets with pre-formed security tabs               

Low maintenance system with no need to repaint/coat

Wrap around gutter outlets for complete flexibility     

High capacity deep-flow gutter profile as standard

Reviews

eKomi Product Feedback

Currently we have no reviews available for this product.

FAQs

Currently we have no content available for this product.

Installation

1. Generally position the fascia brackets at 915mm centres, using at least 3 brackets per gutter length. Use 2 screws on both the left and right fixing options and 1/no underneath the gutter securing tab

 

2. Use a string line to set out your fascia brackets along the gutter run allowing for a fall of 1:600 to 1:350 (max).

 

3. A bead connector is used to join two lengths of gutter. Insert the connector into the front roll of each gutter length. Allow for a 4mm expansion gap.

 

4. An EDPM rubber sealed union connector is used to connect the gutter lengths and angles together. Locate the union connector over the rear edge of the gutter.

 

5. Locate the clasp over the front roll edge of the gutter. Push down on top of the clasp and squeeze the clasp shut. Fold the locking tab over to fully secure.

 

6. Locate the gutter into the fascia bracket and seat level, then fold the front tab of the fascia bracket around the front roll and into the gutter. Fold the rear tab of the fascia bracket down and over the rear edge of the gutter.

 

Outlet Installation

 

1. When installing a ‘wrap around outlet’ mark the desired location of the outlet by drawing a line either side   of   the outlet along   its edge. Draw a further line 20mm inside of the outer lines and join these inner lines together in an oval pattern. This becomes the marking for the cut out hole.

 

2. Use a hacksaw to make an initial hole in the gutter, and then use a set of tin snips to cut out the inner hole that you have marked out.

 

3. Attach the outlet to the gutter and fold the rear tabs of the outlet over the rear edge of the gutter, making sure the outlet is aligned correctly to accept the downpipe.

 

4. Tap the inner rough edges of the hole that was cut in the gutter, down into the outlet, to ensure a smooth flow of water.

 

Downpipe Installation

 

5. Offsets are achieved using 2/no 70º bends, with larger offsets being made by inserting a pipe length between the two bends.

 

6. Downpipes should be installed using at least 2/no pipe clips per length. Mark out the clips locations and level with a sprit level or plumb line. Open the tightening screw to allow the pipe to be inserted, close the clip and re-tighten, making sure not to over tighten and damage the downpipe.

Please wait while we add your product...

Proceed to Checkout

Please enter your details, so we can send your free guide

Please wait while we add your product...

Proceed to Checkout

Please enter your details, so we can send your free guide